Drywall Installation & Repair in Gilbert, AZ

Ceiling drywall is heavier and more difficult to install than wall drywall, and it is more prone to sagging over time if fastened incorrectly. Using the correct thickness, fastener spacing and framing support ensures ceilings remain flat. Ceilings are typically hung before walls so wall panels support the ceiling edges, creating stronger corners.

Texture matching is the single most-failed item on amateur restorations — Arizona's orange-peel and knockdown textures must be matched with the right gun, tip, and air pressure or the patch shows in raking light forever. Popcorn ceilings on pre-1980 homes need asbestos testing before scraping; positive results trigger Maricopa County / ADEQ abatement protocols. Smoke-damaged drywall requires shellac-based primer (BIN, Kilz Original) before topcoat or odor and staining bleed through latex paint within weeks. Water-stained ceilings need full replacement of affected sheetrock once moisture has migrated past the paper face.

Laundry rooms, bathrooms and areas near water heaters benefit from moisture-resistant drywall, which better tolerates humidity than standard board. It is not waterproof, however, and should not be used as a tile backer in showers or tub surrounds, where cement board or another approved backer is required to protect the wall assembly.

Outside corners are protected with corner bead, which creates a straight edge and resists impact damage. Damaged or dented corner bead can be replaced or repaired to restore a clean edge.

Once water-damaged interiors have been dried, restoration includes replacing drywall, insulation, flooring, baseboards and cabinetry that could not be saved, then matching finishes so repairs blend with undamaged areas. Careful matching of paint, texture and flooring is essential for a seamless result.

Hang sequence starts with ceilings, then walls top-to-bottom with butt joints staggered. Fastener spacing per GA-216 — 16" OC on ceilings, 16"–24" OC on walls. All joints taped with paper tape (not mesh on butt joints) bedded in setting-type mud. Three coats minimum, sanded between coats. Primer is shellac-based for any smoke- or water-stained substrate and PVA elsewhere. Texture is applied with calibrated hopper or air-driven gun — we test on cardboard against your existing wall sample to dial in match before spraying. Single-room scope: 3–5 days. Whole-home or full reconstruction: 2–4 weeks.

Additional insulation, resilient channels, specialised sound-dampening drywall and careful sealing can reduce noise transmission between rooms. These options are useful for bedrooms, home offices and media rooms.

Cabinets and built-ins damaged by water, wear or age can frequently be repaired rather than replaced. Swollen panels, loose joints, damaged finishes and worn hardware can be restored, and refinishing can refresh their appearance. Repairing quality built-ins preserves craftsmanship that would be expensive to replicate.

Drywall that has been soaked by water often loses strength and may support mould growth. Saturated drywall is usually cut out and replaced after the wall cavity has been dried. Replacing damaged sections promptly prevents further deterioration.

Original baseboards, door casings, crown moulding and built-ins contribute greatly to a home's character. Damaged sections can often be repaired, and missing pieces can be custom milled to match existing profiles. Preserving original millwork maintains the home's authenticity and is often preferable to replacing it with modern alternatives.

Drywall comes in different types for different locations. Standard drywall suits most walls and ceilings. Moisture-resistant board is used in areas exposed to humidity, though tile in wet areas requires a proper tile backer. Fire-resistant drywall is used where codes require fire separation, such as between an attached garage and living spaces. Choosing the right type ensures safety and performance.

Building codes require fire-resistant construction between an attached garage and the living space, and drywall is a key part of that separation. Using the correct drywall type and sealing penetrations properly maintains the fire barrier. Any openings or damage to garage walls and ceilings should be repaired to preserve this protection.

Installation per GA-216 (Gypsum Association Application & Finishing). Sheet sizes: 1/2" regular for walls, 5/8" Type X for ceilings and garage walls per IRC fire requirements. Joint compound: setting-type for first two coats, lightweight all-purpose for finish coat. Tape: paper for tapered joints, fiberglass mesh only on small patches. Finish levels per GA-214 — Level 4 standard, Level 5 skim coat for areas with critical light or semi-gloss/gloss paint. All work warrantied under ROC #349454.